Beltronics STi Driver Manual de usuario descargar pdf (Pagina 2)

DETECTOR

RADARnode

transmitter

STi Driver

power cord

Jammer

over-ride

POWER IN

Before you begin installation, double check that the RDI

software card and connector cable are correct for your radar

detector. The RDI software card is pre-installed in the side of

the RADARnode transmitter. Always ensure that the

power is OFF before removing or inserting your RDI

software card.

Instal the RADARnode according to the diagram above.

4.1 Remove the Beltronics power cord from your STi Driver.

4.2 Plug the Cheetah RDI connector cable into both the

earphone socket and the power socket of your STi Driver.

4.3 Safely route the RDI connector cable from your STi

Driver to the RADARnode transmitter and plug it into the

RADARnode's socket marked [DETECTOR].

4.4 Plug your Beltronics power cord into the [POWER IN]

socket on the RADARnode.

Use Button 1 on your Cheetah to cycle through the main

menu. Use button 2 (+) and button 3 (-) to adjust the settings

of any menu item and press button 4 to save your changes.

False Alarm Suppression (Button 1)

1. Audible Alert Speed - set the speed limit threshold for

radar alerts, e.g. 35mph. Drive slower and radar alerts are

automatically muted, drive faster and you hear them again.

There is an automatic override for serious alerts (KA

band and laser).

Radar Band Selection (Button 1)

5. X Band 6. K Band 7. KA Band 8. KU Band

Use button 2 (+) and button 3 (-) to enable or disable alerts

for these radar bands, then press button 4 to save.

Voice Only alerts or Voice plus Alert Tones (Button 4)

Pressing button 4, outside of the main menu, swaps the alerts

between “Voice + Tone” alerts (city mute OFF) and “Voice

Only” alerts (city mute ON).

You must change some menu items to enable the RADAR-

node to correctly hear the alerts.

1. Fast Power On Sequence = PwrOn FST

2. Voice Alerts Off = VOICE OFF

3. Volume level is set at 6.5 bars (out of 7)

Setting the volume level can be critical. It may require some

minor adjustments in the level to allow the RADARnode to

function correctly with your individual STi Driver.

7.1 Starting up - Wireless link - A short time after

you switch on your detectors, you will see a small

red wireless symbol appear on the Cheetah GPS

detector. This shows that the wireless datalink is

active and STi Driver alerts will be provided instant-

ly.

7.3 Radar detector alerts - When your Beltronics STi Driver

picks up a signal, a voice alert from your Cheetah will an-

nounce the radar band being picked up.

Warning tones are given for the duration of an alert. There

are different warning tones for each radar / laser band. These

warning tones “ramp-up”, from 1 tone per second, up to 5

tones per second, as the signal strength increases:

POST RAMP UP FIX (BEL CHANGED THE AUDIO TONES IN NOV 2008)

STi display strength 1 is transmitted as signal strength 1

STi display strength 2 is transmitted as signal strength 2

STi display strength 3 is transmitted as signal strength 3

STi display strength 4 is transmitted as signal strength 4

STi display strength 5-7 is transmitted as signal strength 5

PRE RAMP UP FIX

STi display strength 1-4 is transmitted as signal strength 1

STi display strength 5-7 is transmitted as signal strength 5

The actual alert given by your Cheetah may vary occasionally

from the STi display as the RADARnode responds to the

STi’s AUDIO signal and NOT the display.

The Cheetah will alert for as long as the STi Driver does. A

confirmation "chirp" signals the end of an alert.

7.6 Radar Mute - During a radar alert, press button 3 to

mute the remainder of an alert.

7.7 City Mute during an alert - If you want to swap from

VOICE+TONE alerts to VOICE ONLY alerts (or vice versa)

during an alert, you still need to press button 4, but hold it

down for a little longer than normal, until you hear the voice

confirmation that the mode has changed.

8.1 Radar Alerts are not given correctly by the Cheetah

GPS detector.

Make sure that the AudioTones menu setting is not set at

LOUD. They must be set to standard - Tone STD. If prob-

lem persists, adjust the volume level of your radar detector

slightly up or down from 95%.

8.2 Constant KU Band radar alert

RDI software card is not correctly installed. It must be fully

inserted into the slot on the side of the RADARnode. Switch

off power, then remove the card and re-insert flush.

1 2

PRE RAMP UP FIX 2

Comentarios a estos manuales

Sin comentarios

Beltronics STi Driver Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Los detectores de radar Beltronics STi Driver